Calculator
Drywall calculator
Sheets for a room or a set of walls, with tape, joint compound and screws.
Estimate onlySources reviewed 2026-11-14See the sources
What this calculator is for
This drywall calculator works out how many drywall sheets to buy for a room or a set of walls, with doors and windows taken off. It also gives joint tape, joint compound and screws from published coverage figures.
How to measure
- Whole room: measure the floor length and width and the wall height. Choose Walls and ceiling if you are boarding the ceiling too.
- Walls of different heights: choose Separate walls and enter each wall's width and height.
- Measure each door and window opening, width and height, and say how many of that size there are.
The formula
- Wall area, whole room = 2 × (length + width) × height, plus length × width for the ceiling. Separate walls = the sum of width × height.
- Area to cover = wall area − each opening's width × height × how many.
- Sheets = area to cover × (1 + waste ÷ 100) ÷ sheet area, rounded up (S6).
- Finishing, per 1,000 sq ft of area to cover: 370 ft of tape, 11 gal premixed or 80 lb powdered compound, about 1,000 screws or nails (S5).
Worked example
The example "Smallest code-size bedroom" in the start panel: a room 10 × 7 ft with a 7 ft ceiling, walls and ceiling, no door or window taken off, 4 × 8 ft sheets. The sizes have sources (shown with the example).
- Walls: 2 × (10 + 7) × 7 = 238 sq ft. Ceiling: 10 × 7 = 70 sq ft. Area to cover = 308 sq ft.
- Sheets: 308 ÷ 32 = 9.63, rounded up to 10 sheets (no waste added).
- Tape: 308 ÷ 1,000 × 370 = 114 ft. Compound: 3.4 gal premixed or 25 lb powdered. About 308 screws (S5).
- Add doors and windows as openings to take them off; enter a price per sheet under More options to see the cost.
Questions
- Does it include the ceiling?
- Only if you choose Walls and ceiling. The result says which in "What this assumes".
- How much extra should I allow for off-cuts?
- Our sources give no figure for drywall. Nothing is added unless you enter your own percentage under More options.
- Why is the tape worked out without the waste?
- The coverage figures are per 1,000 sq ft of board on the wall (S5), so they use the area to cover, not the extra sheets.
- Can I use metric board sizes?
- Choose Other size under More options and enter the size printed on the board. The standard sizes are listed in feet with their metric equivalents (S6).
- Are doors and windows taken off exactly?
- Their width × height is taken off the wall area. Real off-cuts around openings depend on how the sheets are laid.
Reference: finishing materials per 1,000 sq ft
Scroll the table sideways for more →
| Item | Per 1,000 sq ft | Per 100 m² |
|---|---|---|
| Joint tape | 370 ft | 121 m |
| Premixed joint compound | 11 gal | 44.82 L |
| Powdered joint compound | 80 lb | 39.06 kg |
| Screws or nails | about 1,000 | about 1,076 |
Sheet sizes
| Sheet | Area, sq ft | Area, m² |
|---|---|---|
| 4 × 8 ft | 32 | 2.97 |
| 4 × 10 ft | 40 | 3.72 |
| 4 × 12 ft | 48 | 4.46 |
Sources
- S5: Myron R. Ferguson, "Joint Compound", a drywall project guide in a US building-trade magazine: tape, compound and fastener quantities per 1,000 sq ft of drywall. Full reference in SOURCES.md.
- S6: Manufacturer guide specification for regular gypsum panels to ASTM C1396: width 4 ft (1219 mm), length 8 to 16 ft (2438 to 4877 mm). Full reference in SOURCES.md.
- S8: National Institute of Standards and Technology, Guide to the SI (SP 811), Appendix B.8: 1 ft = 0.3048 m, 1 in = 2.54 cm, 1 lb = 0.45359237 kg, 1 US gal = 3.785411784 L, 1 short ton = 2,000 lb.
Every figure on this page comes from these sources. Where a source gives a range, the calculator shows the range and lets you change the value.